Jeans that need a third cycle, a drum that sits still while the motor hums, or a squeal you can hear from the driveway? A Grapevine technician comes out, isolates the broken component and gets your clothes drying on the first try.
Grapevine, Texas
Gas or electric, most dryer calls we take around Grapevine trace back to one of these six. Each card lists the parts we put a meter on first.
An open heating element, a blown thermal fuse or, on gas units, an igniter that glows but never lights the burner.
Usual suspectsHeating element, thermal fuse, igniter
A broken belt, an idler wheel worn smooth or a motor that hums without the strength to start.
Usual suspectsDrive belt, idler pulley, drive motor
Drum rollers worn flat, a dry rear bearing or worn glides rubbing along the front of the drum.
Usual suspectsDrum rollers, rear bearing, drum glides
Sensor bars coated with dryer sheet residue or a thermostat cutting out before the load is done.
Usual suspectsMoisture sensor bars, cycling thermostat, control board
A door switch that no longer registers the door, a broken start switch or a dead control board.
Usual suspectsDoor switch, start switch, main control
A thermostat stuck closed or a sensor giving the board wrong readings. Pause using it until we check it.
Usual suspectsHigh-limit thermostat, thermistor, heater relay
Dryer Types We Fix
Everyday names and high-end labels alike. If your appliance wears one of these badges, our technicians have opened plenty just like it.
When a dryer quits mid-load, it tends to flash a code first. Match it on the boards below to learn whether to try something or ring us.
Door not detected
The dryer cannot confirm a secure close. Make sure no sleeve is pinched and shut the door firmly.
Try this firstJammed button
A panel button seems stuck. Power off, then press and release each button around its edges.
Try this firstMotor error
The board is getting no proper response from the drive motor.
Call a technicianGas ignition error
The burner on a gas model failed to light during the cycle.
Call a technicianMain control failure
The main board has a fault, which can follow a surge or a loose wire harness.
Call a technicianMoisture sensor problem
Residue may be coating the sensor bars. Clean them using a soft cloth dampened with rubbing alcohol.
Try this firstHeating element open
The element has burned out or a safety fuse in the heat circuit has blown.
Call a technicianDoor switch failure
The switch that reports the door position is worn or misaligned.
Call a technicianCan't find your code here, or does it return as soon as you restart? We will diagnose it in your laundry room.
A few messages from Grapevine neighbors once their towels came out warm and dry.
Dryer was spinning fine but blowing nothing but cold air for days.
Turned out the heating element had burned through. One visit fixed it, and the towels are actually fluffy again.
The squeaking from our dryer could wake the baby two rooms away.
He replaced the worn rollers and now I honestly forget it is on. Worth every penny.
Mine kept stopping after ten minutes with everything still wet.
He cleaned the sensor bars, tested the board and taught me to wipe them every month. Running full cycles again.
Go one question at a time. Yes means move on to the next, and no comes with a simple step you can handle yourself.
Is the dryer getting power when you press Start?
Make sure the plug sits snug in the outlet and reset the breaker. On electric models it is a double breaker, so flip both halves.
Have you emptied the lint screen?
Slide out the screen, clear the fuzz and rinse it whenever it feels waxy from sheets.
Is the door closing with a solid click?
Look for a stray sock in the door opening, then press firmly until you feel the latch catch.
Is the load a normal size for your drum?
Split oversized loads in two, giving clothes space to tumble and dry evenly.
Still damp after all four?
Certified and insured pros are ready to handle the rest.
Tell us which machine is giving you trouble and who made it. Our office rings back to lock in a visit time, and your technician brings the replacement parts that model tends to need.
Service Request
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
